The IsoCore is a derivative of the pyboard. The IsoCore also employs an STM32F405RGT6 with support for a µUSB connection and µSD card, but without the accelerometer of the original pyboard.
The IsoCore breaks out I/O to headers by Port as well as to a PCIeX1 card-edge connector, tailored for a custom ecosystem.
It is intended (but there is no absolute need) to run microPython. As of 1.9.4, the stock image for the pyboard will work with the IsoCore after the 560R mod noted below.
It was developed primarily for this author's own personal ecosystem as a custom development tool.
Rev SEPT18 Eratta:
LED silkscreen matches the markings on the component undersides. This may cause confusion with an assembly house.
With the AP2112K-3.3 Regulator, DNP D5 if using a 12V supply through the edge connector.
If using this board stand-alone with USB, fit a 560R resistor between PA9 and VUSB for USB detection by the board. (An example using a through hole resistor connected to vias can be seen above).
Designer's General Notes
Several odd practices have been incorporated because the author is experimenting:
USB is run both to the connector and to the PCIeX1 card-edge connector, thence onto gasp a ribbon cable bus. Jumpers R14e and R15e may be removed to route solely to the uUSB connector
Vias poke through the silkscreen on the back: It's for information, not for production - it suits this use case.
The PCIeX1 card-edge connector is bastardized for use here. While some pins actually line up with the standard, most do not.
The PCIeX1 connector is common and likely to be available for many years at mainline distributors.
After that, available by desoldering-iron.
It's also a rather pleasant and satisfying feeling to use this kind of connector.
Several units have been built and meet the author's uses:
One batch of bare boards was made at OSHPark
One batch was assembled at MacroFab
No warranty or fitness for a particular use is offered or implied.
License
This project is a derivative of the pyboard, originally developed by Damien P. George with changes made.
No endorsement of this project has been made or asked for.
(Frankly I just made this for my own ecosystem of things in my home lab).
Copyright (c) 2018, Benjamin Bloss
This work is licensed under the Creative Commons Attribution 3.0 Unported License. To view a copy of this license, visit http://creativecommons.org/licenses/by/3.0/ or send a letter to Creative Commons, 444 Castro Street, Suite 900, Mountain View, California, 94041, USA.
{var%20f='http://v.t.sina.com.cn/share/share.php?appkey=1515056452',u=z||d.location,p=['&url=',e(u),'&title=',e(t||d.title),'&source=',e(r),'&sourceUrl=',e(l),'&content=',c||'gb2312','&pic=',e(p||'')].join('');function%20a(){if(!window.open([f,p].join(''),'mb',['toolbar=0,status=0,resizable=1,width=440,height=430,left=',(s.width-440)/2,',top=',(s.height-430)/2].join('')))u.href=[f,p].join('');};if(/Firefox/.test(navigator.userAgent))setTimeout(a,0);else%20a();})(screen,document,encodeURIComponent,'','','https://www.xiaopingtou.cn/data/attach/logo/logo.png', '推荐 aa565938 的问题《STM32玩出新花样，大牛进来看看》','https://www.xiaopingtou.cn/q-157797.html','页面编码gb2312|utf-8默认gb2312'));){kind=link}
The IsoCore breaks out I/O to headers by Port as well as to a PCIeX1 card-edge connector, tailored for a custom ecosystem.
It is intended (but there is no absolute need) to run microPython. As of 1.9.4, the stock image for the pyboard will work with the IsoCore after the 560R mod noted below.
It was developed primarily for this author's own personal ecosystem as a custom development tool.
Rev SEPT18 Eratta:
LED silkscreen matches the markings on the component undersides. This may cause confusion with an assembly house.
With the AP2112K-3.3 Regulator, DNP D5 if using a 12V supply through the edge connector.
If using this board stand-alone with USB, fit a 560R resistor between PA9 and VUSB for USB detection by the board. (An example using a through hole resistor connected to vias can be seen above).
Designer's General Notes
Several odd practices have been incorporated because the author is experimenting:
USB is run both to the connector and to the PCIeX1 card-edge connector, thence onto gasp a ribbon cable bus. Jumpers R14e and R15e may be removed to route solely to the uUSB connector
Vias poke through the silkscreen on the back: It's for information, not for production - it suits this use case.
The PCIeX1 card-edge connector is bastardized for use here. While some pins actually line up with the standard, most do not.
The PCIeX1 connector is common and likely to be available for many years at mainline distributors.
After that, available by desoldering-iron.
It's also a rather pleasant and satisfying feeling to use this kind of connector.
Several units have been built and meet the author's uses:
One batch of bare boards was made at OSHPark
One batch was assembled at MacroFab
No warranty or fitness for a particular use is offered or implied.
License
This project is a derivative of the pyboard, originally developed by Damien P. George with changes made.
No endorsement of this project has been made or asked for.
(Frankly I just made this for my own ecosystem of things in my home lab).
Copyright (c) 2018, Benjamin Bloss
This work is licensed under the Creative Commons Attribution 3.0 Unported License. To view a copy of this license, visit http://creativecommons.org/licenses/by/3.0/ or send a letter to Creative Commons, 444 Castro Street, Suite 900, Mountain View, California, 94041, USA.
我用了maxthon也是左边挡住一部分，chrome才正常
一周热门 更多>